Raven 30/50 V2Instruction ManualR30 R50DDDDD MAIN ROTOR 550mm 600mmDDDDD TAIL ROTOR DIAMETER 9.7 in 9.7 inDDDDD OVERALL LENGTH 46 in 47.5 inDDDDD
From parts bag 2: TheStart Shaft Guide Blocksare pre-assembled. Slidethe Starter Shaft throughone of the block assem-blies with the M5x11 BallBearing
11Step 11B Torque Drive Pinion GearFrom parts bag 2: Using threadlock, insert one M3x4Set Screw (Tip 1) into the gear, note where theflat spot is on
From parts bag 2: Assemble the Constan Tail Drive Gear Assembly (R50), start by pressing the shaftthrough the Counter Gear then selide two M5x7x2
13The Main Gear is pre-assembled with the Auto-Rotation Bearing installed. From parts bag 2: TheMain Shaft has a step in the end of the shaft that is
Tail TransmissionOutput GearAssembly fromStep 11 -Counter GearAssembly fromStep 12Upper Side Frame[HI3107]Main GearAssemblyfrom Step 13M3x12 Self Tapp
15Long hex spacers[HW3127A] x 2M3x35 SocketCap Screws x 4M3 Locknut x 4Insert two long Hex Spacers at the specified locations in the diagram, note th
Position the rear servo mount bracket on the left side of themechanics just behind the main shaft, the front of the mounthas a right angle knotch be
17Step 18 Clutch, Fan & Engine MountingClutchShoes[HW3011]M9x14 FlatWasherEngine ballbearingexposed.Thrust Washeror M9x14 FWFrom parts bag 3, rem
Step 20 Fuel Tank AssemblyFrom parts bag 3, insert the two pieces of aluminum tubing through the large cap, rubber stopper and smallcap, bend the lo
19From parts bag 5, assemble the servo tray using four3x12mm Self Tapping Screws (Tip 3) into the lowerholes of the battery tray. Next install the th
2Table of ContentsTable of Contents ...
Head BlockM3x20 SocketCap Screw &M3 LocknutWashout &SwashplateAssembly fromStep 6Step 24 Final Rotor Head AssemblyFollowing assembly, move th
35mm21From parts bag 6, assemble the landing gear by attaching the Aluminum Skids through the Struts, securingthem with four 3x5mm Set Screws. Set t
Tail Pitch BallLinks x 2M2x8 Pin x 2[HI3089]From parts bag 7: The Tail Pitch Plate and Tail Pitch Ball Links are pre-assembled. (Note: applysome JB
3Building Instructions for the Raven eCCPM helicopter kits.IntroductionCongratulations on your purchase of Century Helicopter Product's newest RC
4Necessary Items “Not Included” in the kit6 Channel Helicopter Radio or Equivalent.Glow Remote Adapter CN222232-40Helicopter Engine50 Helicopter
5This manual has been written for both the Raven 30 and 50 helicopter. CN1060 Raven 30 kit andCN1061 raven 50 kit. The main portion of the manual co
6Rotor head Block[HI3160C]Washout Pins2.6x30mm x 2[HW3170A]Damper Rubber x 2[HI3181]Step 1 Rotor Head BlockFrom parts bag 1: Press in theDamper Rubb
7From parts bag 1: Iznsertthe Feathering Shaft intothe head block, slide oneM6X10 Washer on each side ofthe shaft. Install the blade grip ( Notethe d
STEP 5 Flybar Control Arm AssemblyFrom parts bag 1: Using an availableM3x12 Button Head Screw, insert ap-proximately half the length of the screw tof
9Starting with the inside race, applythreadlock and attach two short balls(Tip 1) directly across from eachother, similarly attach two mediumballs to
Kommentare zu diesen Handbüchern